What are your beliefs on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is conveniently obtainable, the task can relocate quickly; if you need to open up a wall to get rid of the old tub and also place the brand-new bathtub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task and fit trying it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to consider employing one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you mount a new bathtub in your shower room if you have actually already acquired a brand-new bathtub and do not need to alter the arrangement of your previous supply of water pipelines.
Your devices and material checklist need to comprise the following:
Planning for the Setup
Firstly, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome as a result of the limited access that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipes have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Using the two wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the bath tub up until the level checks out degree.
To mount faucets, fit all-time low of the outermost versatile tap port to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water supply and check all joints and also new pipework for leakages as well as tighten them if required. Load the tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has actually been used at least once as this will settle it into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making certain that the washers are in place between the tap as well as the sink. Safeguard the faucet in position with the producer given backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall surface in between the bath and the tiling, resulting in problems with dampness and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealer can fracture fairly early if you do not think about this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly readily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our article about How to Install a Bathtub Yourself. Many thanks for taking a few minutes to read through our article. You should take the opportunity to promote this entry if you enjoyed reading it. Bless you for your time. Please come by our website back soon.
Resolve today, dial!